Plumbing Basics: What You Need for Bathtub Installation
Plumbing Basics: What You Need for Bathtub Installation
Blog Article
We have encountered this article pertaining to How to Install a Bathtub listed below on the internet and accepted it made sense to write about it with you on this site.
Mounting a tub isn't specifically rocket science, yet it does require strong plumbing, woodworking, and often, tiling abilities. Replacing an old tub with a brand-new one is additionally a reasonably tough job. If the old bathtub is readily accessible, the job can move quickly; if you have to open a wall to eliminate the old bathtub and also position the brand-new bath tub, the job is a lot harder. In either instance, the job is within a house handyman's skills, although you will need a helper to move out the old tub as well as set in the new one. See to it you have certified yourself for the work as well as are comfortable trying it. Instead of hiring a professional to take control of a halfway-completed job, it is better to take into consideration utilizing one prior to you start. Chances are you might need a specialist plumber to make tube connections.
This post will certainly assist you install a brand-new bathtub in your restroom if you have currently acquired a new bathtub and also do not need to alter the plan of your previous water pipes.
Your tools and product list need to make up the following:
Removing Old Touches
If you need to replace old taps with new ones as a part of your setup, then the first thing you must do is detach the supply of water. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The process of getting rid of the existing taps can be fairly problematic because of the limited access that is usually the situation.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a cloth ready for the staying water that will originate from the pipelines. When the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from transforming throughout this procedure. Once the faucets have been removed, the holes in the bath/basin will certainly need to be cleansed of any old sealing substance.
Prior to proceeding to fit the brand-new faucets, compare the pipe connections on the old taps to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to stop damage to the string. One end of the adapter fits on the plastic tail of the tap and also the other end gives a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will call for reducing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin making certain that the washers are in place between the tap and the sink. Safeguard the faucet in position with the supplier provided backnut. When the tap is securely in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal tap ports. The former kind ought to be attached to the faucet finishes initially, tightening only by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Installing the Tub
Using both wooden boards under its feet, put the bath tub in the needed placement. The wooden boards are handy in uniformly spreading out the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four little factors.
The following objective is to ensure that the tub is leveled all round. This can be accomplished by checking the level and also adjusting the feet on the bath tub until the level reviews degree.
To install faucets, fit the bottom of the outermost flexible faucet port to the ideal supply pipe by making a compression sign up with; after that do the same for the various other tap.
Turn on the water as well as check all joints and also brand-new pipework for leakages as well as tighten them if necessary. Fill up the bathtub and likewise examine the overflow outlet and the normal electrical outlet for leakages.
Lastly, repair the bath paneling as explained in the producer's instruction manual. Tiling and also sealing around the bath tub ought to wait till the bathtub has actually been used at the very least when as this will resolve it into its last placement.
Getting ready for the Installment
Firstly, the supporting framework provided with the bathroom needs to be fitted (if needed) according to the maker's guidelines. Next off, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is necessary to make sure that if the tap features a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bath, it is also sensible to fit a sustaining plate under the taps system to avoid strain on the tub.
Fit the flexible tap ports to the bottom of both taps using 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bath. Make use of the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you make use of every one of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath should now be ready to be suited its last placement.
Tiling Around the Tub
In the area where the bath meets the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to fracture a rigid seal, creating the water to penetrate the wall in between the bath as well as the tiling, causing issues with moisture as well as possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your components and installations. They are offered in tubes and cartridges, and also are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of soaked newspaper or soft rope. Remember to constantly fill up the bathtub with water prior to securing, to allow for the movement experienced when the bathtub remains in use. The sealer can break relatively very early if you do not think about this movement prior to securing.
Conversely, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally conveniently readily available on the marketplace. It is recommended to fit the tiles using waterproof or water resistant sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I discovered that blog posting about How to Install a Bathtub when looking around the web. Do you know someone else who is excited about the subject? Feel free to promote it. Many thanks for your time. Please check our site back soon.
Dial for results! Report this page